Thermal Bridge Heat Transfer & Vapour Diffusion Simulation Program AnTherm Version 7.126 

[ ← ] [ ↑ ] [ → ] [ToC]

Isolinies / Isotherms (control panel)

The control panel Isolines is used to adjust parameters of isoline evaluations (isotherms, in the case of temperature is chosen for the active evaluation function).

Isolines are shown colorized. Actual colorizing follows values of currently active function (temperature, heat flux, surface humidity etc. - selected within General control panel) and currently selected Colour table.

The isolines (or isotherms) are drawn on component's surface or on slice planes, and are therefore only visible if these evaluations are active also. Settings chosen within control panels Slice X, Slice Y, Slice Z and Surface have thereafter an impact onto evaluation of isolines.

Which isolines are shown can be selectively chosen by setting the number of intervals (#Interv.) or by choosing the step value. Isolines will be created only for values within the interval Min and Max according to the input therein.
At initial view of isotherms the interval of 1°C, starting at 0°C is set and isolines shown.

Isolines can be labelled accordingly also and/or emphasized bolded (as a tube).

Active, Opaque, ColorizeDecide about the visibility, colorizing and transparency of the lines shown
Fixed rangeIf turned on the value range for isolines' creation can be set arbitrarily, independent of the current value range of the evaluated function.
Range-Min/MaxThe values of Maximum and Minimum, shown at the top and bottom of the panel, display the current extent of selected evaluation function.
When "Fixed range" is chosen both values can be set arbitrarily, independent of the current value range of the evaluated function.
Min/MaxThe interval can be reduced by the input in the respective fields.

The input can be performed either by the entry of numeric values into the respective input field or by moving the sliders between the extent values.

#interv.Number of equidistant intervals dividing the extent between the input Min and Max values. The step will be calculated from these values.
StepThe value interval at which isolines shall be drawn.
Start atThe start value fro which (in both directions, towards Min and towards Max) the values of isolines to be drawn shall be calculated.
Bold n-thSelected isolines (each N-th) will be shown emphasized (Bold n-th) - as a thick tube instead of a thin line.
Isoline labels are shown only on bolded lines if the option "Bold n-th" is chosen.
Remark: The tube itself if always partially transparent to allow proper display of isoline labels (visibility test)
Tube RadiusEmphasized isolines (switched on by "Bold n-th") are shown as a tube to better emphasize respective isolines (compared to single pixel thick line). The radius is entered in units of the coordinate system - i.e. millimetres.

Setting the tube radius = 0 will show it as simple line.
The initial value of tube radius is computed based on median extent of component (1/200 of it).

Remark: The number of sides rendered for the tube can be adjusted within application settings.

Clamp rangeLimits the isolines created to the values within the Min/Max interval specified.
If switched off (default) the isolines are created for the whole value range available in the data set.

Remark: It is advisable to adjust the surface "holding" the isolines (i.e. Surface or Slices) by showing it transparent or opaque.
Alternatively adjust colorizing of isolines or the surface "holding" them to dark or bright to receive the required contrast of the image.

Remark: Because slice planes, holding isolines, intersect with model's interior only it is advisable to either turn the view of the surface completely off or show it partially transparent (i.e. not opaque) or show it as wireframe only.
The tooltip of the tab will show up if the surface obscures objects rendered within the interior of the model.

Remark: Isolines are lines shown and colorized by the constant value of the primary function chosen (Isotherms, lines of equal heat flux, lines of equal surface humidity, and so on). Isolines are displayed on construction's surface (Surface) and on slice planes (SliceX,Y,Z) (only if these are active). To show isolines only, without the surface "holding" them, turn that surface completely transparent (set opacity = 0). The selection of values at which isolines are shown is givien by the definition of a start value (Start at) and of a interval length (Step) (or number of intervals).

Remark: The visibility of isolines is directly dependant on the visibility of the surface object holding it:
→ Isolines on the component's surface are only visible if the Surface is also active. To get better view onto isolines turn the surface transparent  – Surface→Opacity=0.0;
→ Isolines on slices (X/Y/Z) are only shown if the respective slice is also active. To get better view onto isolines turn the respective slice transparent – SliceX/Y/Z→Opacity=0.0

Hint: Fix the Range to receive comparable results by decoupling it from the actually evaluated domain. This function specific setting takes care for keeping the range constant regardless of changes to boundary conditions, evaluation time point, animation or for different projects.

 

See also: Results 3D window, Active (setting), Opaque and Opacity (setting), Colorize (setting), Solid or Wireframe (setting), General (control panel), Active Function, Isosurface (control panel), Labels (control panel), Fixed Range (setting)


 Model, Calculate, Simulate and Analyse Thermal Heat Bridges in 2D and 3D with AnTherm® 

[ ← ] [ ↑ ] [ → ] [ToC

 Copyright © Kornicki Dienstleistungen in EDV & IT

2014-03-04 10:19 +0100